Name | UP Stringtown Road Bridge Chicago & Alton Railroad Bridge #130.3 |
Built By | Chicago & Alton Railroad |
Currently Owned By | Union Pacific Railroad |
Superstructure Contractor | Unknown |
Substructure Contractor | Unknown |
Length | 33 Feet Total |
Width | 2 Tracks, 1 In Use |
Height Above Ground | 13 Feet 7 Inches |
Superstructure Design | Through Plate Girder |
Substructure Design | Concrete |
Date Built | 1924 |
Traffic Count | 20 Trains/Day (Estimated) |
Current Status | In Use |
Chicago & Alton Railroad Bridge Number | 130.3 |
Union Pacific Railroad Bridge Number | 130.30 |
Significance | Local Significance |
Documentation Date | 4/2/2023 |
In 1850, the Alton and Sangamon Railroad began construction on a 220 mile railroad line, extending from Joliet, Illinois to Alton, Illinois; with stations in Bloomington and Springfield, Illinois. The railroad was acquired by the Chicago, Alton & St. Louis Railroad and completed in 1855. The Alton and St. Louis Railroad constructed a 22 mile line from Alton to East St. Louis in 1856. The railroads were reorganized as the St. Louis, Alton & Chicago Railroad in 1857, and was merged into the Chicago & Alton Railroad (C&A) in 1862. The C&A developed several lines throughout central Illinois, and this route made up the principal mainline of the system. A bypass of Alton between Godfrey and East St. Louis was constructed in As traffic grew on the system through the 1870s and 1880s, the need for a second track became apparent. A second track was added in 1870 between Mazonia and Odell, from 1888 to 1893 between Odell and Bloomington, and through Springfield in 1893. This route became an important route to the Illinois railroad network, providing the most direct connection between St. Louis and Chicago.
Throughout the years, the C&A would be affiliated with several
larger railroads, and the railroad primarily operated as a bridge
route. The C&A was reorganized in 1901, and until 1906 was owned by
the Atchison, Topeka & Santa Fe Railway and the Chicago, Rock
Island & Pacific Railway. Between Bloomington and Springfield, a second track was constructed in 1907, and a second track was constructed in 1911 between Springfield and East St. Louis. A large realignment was made between Atlanta
and Lawndale in 1924. In 1931, the C&A would be reorganized as the Alton Railroad (A), a
subsidiary of the Baltimore & Ohio Railroad. The Alton was sold to
the Gulf, Mobile & Ohio Railroad (GM&O) in 1949, and the various
subsidiaries consolidated at that time. The GM&O merged with the
Illinois Central Railroad to form Illinois Central Gulf (ICG) in 1972.
During the ICG years, the route was downgraded, and the second track mostly removed. This line was excess for the ICG, and the route would be sold to the
Chicago, Missouri & Western Railway (CM&W) in 1987. The CM&W went bankrupt, and the line was sold to the Southern Pacific Railroad in 1989, which became part of Union Pacific Railroad in 1996. During the 2010s, the route was rebuilt for high speed rail. Today, Union Pacific continues to operate this route as the Joliet Subdivision between Joliet and Bloomington, and the Springfield Subdivision between Bloomington and East St. Louis. High speed Amtrak trains also utilize this route.
Located south of Bloomington, this through plate girder bridge carries the former Chicago & Alton Railroad over Stringtown Road (County Road 1000N). It is unknown if there was a previous bridge at this location. Built in 1924, the current bridge consists of a 33-foot through plate girder span, set onto concrete abutments. The abutments were constructed wide enough for three tracks, although it appears only a two track structure was ever built. Typical of C&A bridges from this era, the bridge utilizes square girder ends and a ballast floor. In addition, the bridge runs at a heavy skew. Ballast decks were preferred by both railroads and roadway agencies, as they reduced the required less overall maintenance and provided a safer passage for the public crossing under the structure. The floor of the span is traditionally composed, using six stringers and floor beams. The ballast deck is constructed of a cast in place concrete slab. The superstructure was fabricated by an unknown contractor, and the substructures were also built by an unknown contractor. Through plate girder bridges were popular for railroad use, as they were durable and easy to construct. Since the initial construction, the bridge has seen few alterations. The east track is currently unused, while the west track is in use. Overall, the bridge appears to be in fair condition, with no significant deterioration noted. The author has ranked this bridge as being locally significant, due to the common design.
Citations
Build date | Date stamp |
Railroad History Citation | ICC Valuation Information, Compiled by Richard S. Steele |