| Name | UP Indian Creek Bridge (Council Bluffs, North) Chicago & North Western Railway Bridge #1090 |
| Built By | Chicago & North Western Railway |
| Currently Owned By | Union Pacific Railroad |
| Superstructure Contractor | Unknown (West Track) Paxton-Vierling Steel Company of Omaha, Nebraska (East Track) |
| Substructure Contractor | Unknown |
| Length | 57 Feet Total (West Track), 82 Feet Total (East Track) |
| Width | 2 Tracks |
| Height Above Ground | 15 Feet (Estimated) |
| Superstructure Design | Through Plate Girder |
| Substructure Design | Concrete |
| Date Built | 1919 (West Track) 1997 (East Track) |
| Traffic Count | 50 Trains/Day (Estimated) |
| Current Status | In Use |
| Chicago & North Western Railway Bridge Number | 1090 |
| Union Pacific Railroad Bridge Number | 350.71 |
| Significance | Local Significance |
| Documentation Date | 2/5/2017; 5/5/2017 |
In 1867, the Cedar Rapids & Missouri River Railroad (CR&MR) continued constructing a mainline westward from Boone, Iowa. In the late 1850s and early 1860s, the CR&MR had participated in constructing a line from Clinton, Iowa to Boone. The CR&MR was leased by the Chicago & North Western Railway (C&NW), which was seeking a route connecting Chicago to the Missouri River. In 1867, an impressive 150 miles were constructed between Boone, Iowa and Council Bluffs, Iowa, completing a connection between Chicago and the Missouri River. The line also allowed for a short spur from Missouri Valley, Iowa to the Missouri River opposite of Blair, Nebraska. This spur would eventually be extended across the Missouri River and into Nebraska. Between 1869 and 1872, Union Pacific Railroad (UP) constructed a bridge across the Missouri River between Council Bluffs and Omaha, Nebraska; and the C&NW obtained trackage rights over the bridge to reach Omaha. During the second half of the 19th Century, the C&NW had constructed and acquired a large amount of trackage throughout the Midwest. In 1884, the CR&MR was formally purchased by the C&NW; and this line quickly became a core asset of the C&NW system.
By the late 19th Century, traffic over this line had increased to the point significant upgrades were required. In 1893, a 5-mile section of railroad was relocated west of Jefferson, Iowa to improve grades and eliminate curves. One of the most significant barriers to efficient operation over this line was the Des Moines River Valley between Boone and Ogden, Iowa. The original route crossed the Des Moines River at Moingona, which was approached by winding and steep approaches on each bank. In 1899, C&NW subsidiary Boone County Railway (BCR) began construction on a more direct route between Boone and Ogden, Iowa; including a massive viaduct across the Des Moines River. The BCR was consolidated into the C&NW in 1900, and the new cutoff was completed in May 1901. The new alignment shortened the route by 3 miles, cut grades in half and only required two small curves. The original mainline through Moingona was maintained as an emergency backup and to serve industries in the area. Between 1901 and 1902, a second track was also constructed between Ogden and Council Bluffs, including a 5-mile realignment near Arcadia, Iowa. The double tracking of this line provided the C&NW with a well constructed double track mainline between Chicago and Council Bluffs.
By the 20th Century, the C&NW was operating an extensive railroad network, which radiated north and west from Chicago. The original mainline into Moingona was abandoned in 1930. This line served as the backbone of the C&NW, connecting transcontinental freight and passengers at Omaha to Chicago. Known as the Overland Route, this line became one of the most significant railroad routes in the United States. This route saw continuous upgrades during the 20th Century, including significant bridge, rail, tie and signal upgrades. In 1995, the C&NW was purchased by UP, which provided UP with a mainline into the railroad hub of Chicago. Into the 21st Century, the line has seen continuous upgrades, and remains one of the most significant railroad lines in the United States. Today, UP operates this line as the Boone Subdivision between Boone and Missouri Valley; and the Omaha Subdivision between Missouri Valley and Council Bluffs.
Located immediately at the former alignment of 11th Street in Council Bluffs, this through plate girder bridge carries a former Chicago & North Western Railway mainline over Indian Creek at Creek Top. Since Council Bluffs was first settled, Indian Creek had been known for disastrous floods due to its narrow valley and small tributary area. The first bridge at this location likely consisted of a single track timber pile bridge. In 1891, the facilities at Council Bluffs were significantly upgraded, and new bridges were constructed at this location. The 1891-era bridges consisted of several single track through plate girder spans, set onto timber pile abutments. The crossing consisted of Bridge #1090, which included two main tracks on the west end; Bridge #1090AA, which included a third side track immediately east of Bridge #1090; and Bridge #1090A, which included two additional yard lead tracks on the east end. In 1915, new abutments were constructed for Bridge #1090 and Bridge #1090A, while Bridge #1090AA retained timber abutments. Bridge #1090 was reconstructed with two new single track through plate girder spans in 1919, and the old spans were reused at Bridge #D-37B across the Wisconsin River at Wausau, Wisconsin in 1922. Bridge #1090AA was reconstructed with a new single track through plate girder span and concrete abutments in 1929. The bridge remained in this configuration until the mid-1950s, when the eastern track of Bridge #1090A was removed. In the early 1970s, Bridge #1090AA and the eastern track of Bridge #1090A were removed. It is unclear if the span from Bridge #1090AA was reused elsewhere. After the C&NW was acquired by Union Pacific Railroad in 1995, the crossing became an important connection between the two systems, and in 1997 the bridge was reconfigured to improve operations. As part of the work, the remainder of Bridge #1090A was removed, and a new through plate girder span installed immediately east of the remaining span of Bridge #1090, giving the bridge its present configuration.
Currently, the bridge consists of a 57-foot through plate girder span for the west track and an 82-foot through plate girder span for the east track. Both spans are set onto concrete abutments and run at a slight skew. The west track span uses a standard design for the era, with heavy girders, rounded and tapered girder ends and a standard floor. The east track span uses a modern design, with heavy welded girders and tapered girder ends. The abutments consist of rectangular concrete structures, which are located behind the channel walls of the creek. An unknown contractor fabricated the west track superstructure, while the east track superstructure was fabricated by the Paxton-Vierling Steel Works. An unknown contractor also constructed the concrete abutments. Through plate girder spans were popular for railroad use, due to the durability and ease of construction. In 1936, Indian Creek was channelized and covered by a concrete slab. To construct the channel, new concrete walls were constructed and the space between the walls and abutments filled. Today, both tracks remain in regular use. Overall, the bridge appears to be in fair condition, with no significant deterioration noted. The author has ranked this bridge as being locally significant, due to the common design.
Citations
| Build date (west track superstructure) | Chicago & North Western Railway Drawing Collection at the Chicago & North Western Historical Society Archives |
| Build date and builder (east track superstructure) | Paxton-Vierling Steel Company plaque |
| Railroad History Citation | ICC Valuation Information, Compiled by Richard S. Steele |